Plastic Tower Packing

  • Plastic Rosette Ring Random Packing

    Plastic Rosette Ring Random Packing

    Plastic Teller Rosette Ring is the first A.J.Teller by the United States in 1954 out of research and development, and therefore also often referred to as the garland wreath Taylor (Teller Rosette). This filler is composed of many ring formed around the knot, because the department can fill the gap for a higher liquid holdup, the liquid column can stay longer, thus increasing the two-phase gas-liquid contact time, improve the packing efficiency of mass transfer. Polypropylene packing with porosity, and pressure drop and low height of mass transfer unit, the pan-point high, vapor-liquid contact with the full, the proportion of small, high efficiency and mass are used for gas scrubbing, purifying tower.

  • Plastic Intalox Saddle Ring Tower Packing

    Plastic Intalox Saddle Ring Tower Packing

    The Plastic Intalox Saddle is made from heat resistant and chemical corrosion resistant plastics, including polypropylene (PP), polyvinyl chloride (PVC), chloridized polyvinyl chloride (CPVC) and polyvinylidene fluoride (PVDF). It has features such as large void space, low pressure drop, low mass-transfer unit height, high flooding point, uniform gas-liquid contact, small specific gravity, high mass transfer efficiency and so on, and the application temperature in media ranges from 60 to 280℃. For these reasons it is widely used in the packing towers in petroleum industry, chemical industry, alkali-Chloride industry, coal gas industry and environmental protection, etc.

  • Plastic Super Intalox Saddle Ring Tower Packing

    Plastic Super Intalox Saddle Ring Tower Packing

    The shape of the Intalox Saddle Ring is a combination of the ring and the saddle, which benefits the advantages of the two. This structure helps liquid distribution and enlarges the quantities of gas holes. The Intalox Saddle Ring has less resistance, bigger flux and higher efficiency than the Pall Ring. It is one of the most widely used packing with good hardness. It has low pressure, big flux and high efficiency of mass transfer, and it is easy to manipulate.

  • 25 38 50 76 mm Plastic Pall Ring Tower Packing

    25 38 50 76 mm Plastic Pall Ring Tower Packing

    Plastic Pall Ring packing is a high hole diameter equal to the packing ring, each window there are five tongue leaves, each leaf tongue ring in turn point to heart, upper and lower levels of the location of the opposite window at different times and in general Central area of wall openings about the total area of about 30%. With porosity, and pressure drop and low height of mass transfer unit, the pan-point high, vapor-liquid contact with the full, the proportion of small, high mass transfer efficiency.
    This structure improves the vapor-liquid distribution, make full use of the inner surface of the ring, so that the tower fill the gas and liquid form from the free passage.

  • PTFE Pall Ring Tower Packing

    PTFE Pall Ring Tower Packing

    PTFE Pall Ring packing has large flux, small resistance, high separation efficiency and operational flexibility.

  • Plastic Rachig Ring Tower Packing

    Plastic Rachig Ring Tower Packing

    Before the invention of the tower packing shape by Frederick Raschig in 1914, Plastic raschig ring is the most early-developed product in random packing. Plastic Rachig Ring has a simple shape with equal length at its diameter and height. It provide a large surface area within the volume of the column for interaction between liquid and gas or vapour.

  • PTFE Raschig Ring Tower Packing

    PTFE Raschig Ring Tower Packing

    PTFE Raschig Ring packing has large flux, small resistance, high separation efficiency and operational flexibility.

  • Plastic Random Packing Heilex Ring

    Plastic Random Packing Heilex Ring

    Plastic Heilex Ring is a new type of injection molding of the filler hole, it was first being developed in foreign countries. Later, China’s such a filler were studied, and the successful development of China-made Heilex ring packing. Plastic Heilex Ring shape so that it not only has the flux, and pressure reduction and anti-corrosion resistance and good impact performance, but also has a filler would not nested, the wall flow effect of the small and the advantages of gas-liquid distribution. This applies to gas absorption packing, cooling and gas purification processes. It is a new kind of open-celled packing. Heilex ring has unique configuration, and usually made by PP injection. Plastic heilex ring enlarges its surface area and void space which contribute a lot to enhance the product performance. We can provide heilex rings in a variety of plastic, such as PP, RPP, PE, PVC, CPVC, PVDF etc.

  • Plastic Tri-Pak ball packing for water treatment

    Plastic Tri-Pak ball packing for water treatment

    Zhongtai Tri-pak tower random packing, which is similar as polyhedral hollow ball packing, provides maximum surface contact between the gas and the scrubbing liquid by facilitating continous formation of droplets througout the packed bed. This result in high scrubbing efficiency, and minimizes total packing depth required. It can also prevent clogging, because there are no flat surface to harbor particulates. Tri-pak tower packing eliminates puddling too. Because its free of corners and valleys, and minimizes wasteful liquid flow down the wall surface. Tri-pak further prevent dry spots and compression interlock, two phenomena common to traditional packing media. Both conditions cause liquid and air channelling and decrease media efficiency.

  • Plastic Polyhedral Hollow Ball for water treatmenet

    Plastic Polyhedral Hollow Ball for water treatmenet

    Polyhedral Hollow Ball packing is made from heat resistant and chemical corrosion resistant plastics, and the application temperature in media ranges from 60 to 150 degrees.

    Plastic Polyhedral Hollow Ball (PP, PE, PVC, CPVC, RPP ) is also called plastic multi-aspect hollow ball, polyhedral hollow ball packing composed of two hemispheres which will form into a ball. And each hemisphere consists of a number of half fan-shaped leaves, the upper and lower leaves in a staggered arrangement. The design concept is advanced and the structure is reasonable. Plastic Polyhedral hollow balls have the virtue of light weight, wide free space, small wind resistance, and good surface hydrophilic, big full wet surface area and convenient filling in the equipment and sound usage effect.

  • Plastic Hollow Floating Ball For Sewage Treatment

    Plastic Hollow Floating Ball For Sewage Treatment

    Plastic Hollow Floating Ball help control heat loss, evaporation, and help with odor and mist control. Hollow Balls are also used as a check-valve ball in flow control applications.

    Plastic Hollow Floating Ball is made from heat resistant and chemical corrosion resistant plastics. It has features such as high free volume, low pressure drop, low mass-transfer unit height, high flooding point, uniform gas-liquid contact, small specific gravity, high mass transfer efficiency and so on, and the application temperature in media ranges from 60 to 150. For these reasons it is widely used in the packing towers in petroleum industry, chemical industry, alkali-Chloride industry, coal gas industry and environmental protection, etc.

  • Plastic Liquid covering ball for Water Treatment

    Plastic Liquid covering ball for Water Treatment

    Plastic Liquid-surface covering ball is characteristic of stable barycenter, super position side by side, and excellent covering performance. This product is widely used in coagulate water tank and salt eliminating water tank in water treatment.
    Ways of using:

    Put in a certain quantity of the as per the surface area of the water or liquids surface area, and the balls will set out and distribute themselves in an orderly way, and covers the surface area, and seal the fringe with sealing material.

123 Next > >> Page 1 / 3